{"id":2285,"date":"2026-05-08T09:30:19","date_gmt":"2026-05-08T09:30:19","guid":{"rendered":"https:\/\/www.agriculturalparts.top\/application\/pto-shaft-for-pto-generator-pto-alternator\/"},"modified":"2026-05-08T09:30:19","modified_gmt":"2026-05-08T09:30:19","slug":"pto-shaft-for-pto-generator-pto-alternator","status":"publish","type":"post","link":"https:\/\/www.agriculturalparts.top\/uk\/application\/pto-shaft-for-pto-generator-pto-alternator\/","title":{"rendered":"PTO Shaft for PTO Generator \/ PTO Alternator"},"content":{"rendered":"

PTO Shaft for PTO Generator & PTO Alternator \u2014 Stable Power Delivery for On-Farm Electricity Generation<\/h2>\n

The PTO generator shaft<\/strong> \u2014 also known as a PTO alternator driveshaft<\/em>, tractor generator cardan shaft<\/em>, farm power generator PTO driveline<\/em>, or emergency generator PTO drive shaft<\/em> \u2014 connects the tractor’s power take-off to the input shaft of a PTO-driven AC generator or alternator unit, enabling the tractor to serve as a mobile power station for on-farm irrigation pump drives, workshop power, grain handling equipment, emergency lighting, and remote rural electrical supply.<\/p>\n

PTO generators are widely used across Australian agriculture \u2014 particularly in areas with unreliable grid power, remote properties beyond grid reach, and emergency backup applications during storm damage to utility infrastructure. The PTO shaft for a generator application has unique engineering requirements compared to all other PTO applications: absolute speed consistency<\/strong> (generator output frequency is directly proportional to shaft RPM \u2014 any variation produces frequency deviation that damages sensitive electronics), long continuous duty capability<\/strong> (generators often run for 6\u201348 hours continuously during emergencies), and zero overload protection need<\/strong> (generators are inherently current-limited by their control circuitry \u2014 no cam or friction protection is typically needed). Our PTO generator shaft<\/strong> (Series 4\/5) delivers the precision-balanced, continuously-rated drive that electrical generation demands.<\/p>\n

\"PTO<\/p>\n

Browse our PTO generator shaft range<\/a> or contact our team<\/a> for generator driveline specifications.<\/p>\n

Technical Specifications \u2014 PTO Shaft for PTO Generator \/ PTO Alternator<\/h2>\n
\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
Parameter<\/th>\nStandard Value<\/th>\nCustomisable Range<\/th>\n<\/tr>\n<\/thead>\n
Series<\/td>\nSeries 4 \/ Series 5<\/td>\nSeries 3\u20136<\/td>\n<\/tr>\n
PTO Speed<\/td>\n540 RPM (most generators) \/ 1000 RPM<\/td>\n540 \/ 1000 RPM<\/td>\n<\/tr>\n
Power Rating<\/td>\nUp to 65 kW<\/td>\n15\u2013120 kW<\/td>\n<\/tr>\n
Continuous Duty Rating<\/td>\n100% continuous rated<\/td>\n100% \u2014 no intermittent derate<\/td>\n<\/tr>\n
Generator Output (typical)<\/td>\n10\u201380 kVA (0.8 pf)<\/td>\n5\u2013150 kVA<\/td>\n<\/tr>\n
Compressed Length<\/td>\n600\u2013840 mm<\/td>\n440\u20131,600 mm<\/td>\n<\/tr>\n
Extended Length<\/td>\n960\u20131,380 mm<\/td>\n670\u20132,200 mm<\/td>\n<\/tr>\n
Tube Profile<\/td>\nTriangular \/ Star<\/td>\nTri \/ Star<\/td>\n<\/tr>\n
CV Joint<\/td>\nStandard (if gen. is fixed \u2014 cross-joint OK)<\/td>\nCross-joint \/ CV \u00b130\u00b0<\/td>\n<\/tr>\n
Working Angle<\/td>\n\u00b115\u00b0 (fixed gen. typically small angle)<\/td>\n\u00b115\u00b0 to \u00b130\u00b0<\/td>\n<\/tr>\n
Input Spline<\/td>\n1-3\/8″ \u00d7 6 spline<\/td>\n1-3\/8″\u00d76 \/ 1-3\/4″\u00d720<\/td>\n<\/tr>\n
Output (Generator Input)<\/td>\nSAE-B or SAE-C flange \/ 1-3\/8″\u00d76<\/td>\nSAE A\/B\/C flange \/ spline<\/td>\n<\/tr>\n
Overload Protection<\/td>\nFriction clutch (optional \u2014 generator self-limits)<\/td>\nFriction \/ None (generator loads self-limit)<\/td>\n<\/tr>\n
Slip Torque (if fitted)<\/td>\n800\u20131,200 N\u00b7m<\/td>\n300\u20132,000 N\u00b7m<\/td>\n<\/tr>\n
Balance Class<\/td>\nISO G2.5 (frequency-critical applications)<\/td>\nG6.3 \/ G2.5<\/td>\n<\/tr>\n
Guard Type<\/td>\nFull-cone PE UV-stable<\/td>\nFull \/ Half cone PE<\/td>\n<\/tr>\n
Grease Interval<\/td>\nEvery 8 hours operation \/ Every 50 hrs long-run<\/td>\n8\u201350 hrs by application<\/td>\n<\/tr>\n
Sealed Cross-Kits<\/td>\nIP55 standard (outdoor generator use)<\/td>\nIP55<\/td>\n<\/tr>\n
Surface Finish<\/td>\nZinc plate + UV-stable enamel<\/td>\nVarious<\/td>\n<\/tr>\n
Yoke Material<\/td>\nForged 20CrMnTi \/ 40Cr<\/td>\n20CrMnTi \/ 40Cr<\/td>\n<\/tr>\n
Temp Range<\/td>\n-20 \u00b0C to +80 \u00b0C<\/td>\n-40 \u00b0C to +100 \u00b0C<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n

Working Principle of the PTO Generator Shaft \u2014 Precision Speed for Clean Power<\/h2>\n

A PTO-driven generator operates on a fundamental principle: the generator rotor (typically a 4-pole synchronous machine) must rotate at exactly 1,500 RPM to produce 50 Hz AC power (the Australian standard). With most generators specified for 540 RPM PTO input, this requires a 1:2.78 step-up gearbox inside the generator set. The PTO shaft delivers 540 RPM to this gearbox input; the gearbox steps up to 1,500 RPM at the generator rotor.<\/p>\n

Any variation in the PTO shaft’s rotational speed translates directly to generator output frequency variation. Modern inverter-generator electronics can tolerate \u00b12% frequency variation (49\u201351 Hz) without issue, but sensitive agricultural electronics (variable-speed drives, PLCs, computer systems) may suffer damage or control errors at variations exceeding \u00b10.5%. Our G2.5 precision-balanced shaft maintains RPM variation below \u00b10.5% at 540 RPM under full generator load \u2014 the tightest control available in an agricultural shaft design. For 1,000 RPM PTO generator applications (generating 50 Hz via 3,000 RPM 2-pole machines), G2.5 balance at 1,000 RPM is even more critical and is our standard specification.<\/p>\n

\"PTO<\/p>\n

Core Advantages of Our PTO Shaft for PTO Generator \/ PTO Alternator<\/h2>\n
\n
\n

\u26a1 G2.5 Precision Balance for Frequency Stability<\/strong><\/p>\n

ISO G2.5 dynamic balance at 540 or 1,000 RPM maintains shaft-induced frequency variation below \u00b10.2 Hz \u2014 protecting sensitive agricultural electronics connected to PTO generator power from shaft-vibration-induced frequency fluctuation.<\/p>\n<\/div>\n

\n

100% Continuous Duty Rating<\/strong><\/p>\n

All components \u2014 cross-kits, tube profile, guard, grease volume \u2014 dimensioned for 100% continuous operation without service interval interruption. Standard agricultural shafts are derated for continuous duty; generator shafts are not.<\/p>\n<\/div>\n

\n

SAE Flange Generator Input Options<\/strong><\/p>\n

SAE-A, SAE-B, and SAE-C 2-bolt flange output yokes available for direct coupling to generator input flanges \u2014 the standard connection method for quality generator sets that provides superior alignment over spline connections for frequency-sensitive continuous duty.<\/p>\n<\/div>\n

\n

\ufe0f IP55 for Outdoor Generator Use<\/strong><\/p>\n

PTO generators are frequently operated outdoors during storm emergencies in rain, damp, and post-storm conditions. IP55 sealed cross-kits prevent moisture infiltration during continuous outdoor operation \u2014 critical for generators used during post-cyclone or bushfire infrastructure recovery.<\/p>\n<\/div>\n

\n

\u23f1\ufe0f Extended 50-Hour Grease Interval (Sealed)<\/strong><\/p>\n

50-hour greasing intervals with IP55 sealed cross-kits enable 48+ hour continuous emergency generation sessions without maintenance interruption \u2014 meeting the continuous duty requirements of post-disaster infrastructure recovery operations.<\/p>\n<\/div>\n

\n

SAA\/ESV Compliance Documentation<\/strong><\/p>\n

CE Declaration of Conformity and dimensional inspection reports supplied \u2014 supporting electrical safety compliance documentation for PTO generator installations under AS\/NZS 3000 (Wiring Rules) and state electrical safety acts.<\/p>\n<\/div>\n<\/div>\n

Brand Compatibility & Cross-References<\/h2>\n

Direct drop-in replacement for OEM shafts on: Genelec, FG Wilson, Stamford, Mecc Alte, Leroy-Somer, Linz Electric, Pramac, PowerLand<\/strong>. 12,000+ cross-references verified before dispatch.<\/p>\n

\u26a0\ufe0f Brand names cited for parts-compatibility identification only. No commercial affiliation claimed.<\/em><\/p>\n

Spare parts stocked:<\/strong> S3\u2013S8 cross-kits (open \/ IP55 \/ IP67) \u00b7 Cam spring sets \u00b7 Friction disc sets \u00b7 Impact-resistant PE guards \u00b7 Retaining chains \u00b7 Yoke collars \u00b7 SAE flange adaptors<\/p>\n

\u2192 Browse all PTO shaft accessories<\/a><\/p>\n

Compliance & Regional Demand<\/h2>\n

Standards & Regulations:<\/strong> Standards: ISO 5673-1:2014, AS\/NZS 3000 (Wiring Rules \u2014 generator installation), AS 2790 (electricity generating sets). AS 4024.3601 PTO guarding. State electrical safety: ESV (VIC), SafeWork NSW, DNRME QLD \u2014 PTO-driven generators require electrical safety inspection and tagging by a licensed electrician before connection to premises wiring. AS 1418.17 (cranes \u2014 mobile generator integration) where applicable.<\/p>\n

Key Demand Regions:<\/strong> Key demand regions: Remote WA (off-grid properties), NT rural (Darwin surrounds), FNQ (cyclone emergency backup), Remote QLD (channel country), Outback NSW\/SA (isolated properties), Rural VIC (post-storm backup for dairy farms).<\/p>\n

CE Declaration, ISO material certs, and dimensional inspection reports supplied. GST-inclusive AUD invoicing.<\/p>\n

Quick Selection Guide<\/h2>\n
\n\n\n\n\n\n\n\n\n\n\n
Parameter<\/th>\nHow to Determine<\/th>\nGuidance<\/th>\n<\/tr>\n<\/thead>\n
Generator output (kVA)<\/td>\nFrom generator spec plate<\/td>\nMatch shaft power rating \u2265 generator rated kVA \u00d7 1.25<\/td>\n<\/tr>\n
PTO speed required<\/td>\n540 or 1000 RPM \u2014 CRITICAL<\/td>\nConfirm on generator nameplate before ordering<\/td>\n<\/tr>\n
Generator input coupling<\/td>\nSAE flange \/ Spline \/ Direct drive<\/td>\nSAE flange preferred for continuous duty alignment accuracy<\/td>\n<\/tr>\n
Duty cycle<\/td>\nEmergency occasional \/ Regular seasonal \/ Continuous backup<\/td>\nContinuous backup: sealed cross-kits + 50 hr interval + G2.5 balance<\/td>\n<\/tr>\n
Generator mounting<\/td>\nFixed to tractor 3PL \/ Trailer-mounted \/ Ground-fixed<\/td>\nFixed 3PL: standard shaft; ground-fixed: measure alignment carefully<\/td>\n<\/tr>\n
Electronics connected<\/td>\nSensitive VSD\/PLC \/ General farm load<\/td>\nSensitive electronics: G2.5 balance mandatory<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n

Installation Guide<\/h2>\n
    \n
  1. [Electrical safety \u2014 licensed person]<\/strong> Licensed electrician required for all generator-to-premises connections. PTO shaft installation is mechanical \u2014 but electrical commissioning must be by a licensed person.<\/li>\n
  2. [Alignment measurement]<\/strong> Position generator set relative to tractor; measure PTO stub to generator input face.<\/li>\n
  3. [Axial alignment critical]<\/strong> Align generator input shaft axis with PTO axis before shaft installation \u2014 misalignment causes rapid CV joint wear even at small angles.<\/li>\n
  4. [Tractor connection]<\/strong> Apply anti-seize to PTO splines; install cross-joint or CV yoke (per angle); engage locking pin.<\/li>\n
  5. [Generator connection]<\/strong> Connect SAE flange output to generator input; torque flange bolts to generator spec.<\/li>\n
  6. [Guard \u2014 UV-stable mandatory for outdoor use]<\/strong> Fit full-cone UV-stable guard; anchor both chains \u2014 generator may be stationary while tractor engine runs for extended periods.<\/li>\n
  7. [Frequency verification]<\/strong> Start tractor; engage PTO at idle; allow generator rotor to reach speed; check output frequency on generator panel (should read 50 Hz \u00b1 0.5 Hz).<\/li>\n
  8. [Load verification]<\/strong> Do not load generator until frequency is stable. After full load application, re-verify frequency. Grease at 8-hour intervals (50 hrs sealed).<\/li>\n<\/ol>\n

    \"PTO<\/p>\n

    \ufe0f Troubleshooting<\/h2>\n
    \n\u26a0\ufe0f Generator output frequency unstable (48\u201352 Hz fluctuation)<\/summary>\n
    \n

    Root Cause:<\/strong> PTO shaft vibration from worn cross-joint or imbalance causing speed variation<\/p>\n

    Fix:<\/strong> Replace cross-kits; check shaft balance at 540\/1000 RPM \u2014 G2.5 balance required for frequency-sensitive loads<\/p>\n<\/div>\n<\/details>\n

    \n\u26a0\ufe0f Generator output voltage fluctuating in phase with shaft rotation<\/summary>\n
    \n

    Root Cause:<\/strong> Shaft imbalance inducing mechanical vibration into generator rotor \u2014 causing stator-rotor air gap variation<\/p>\n

    Fix:<\/strong> Return shaft for G2.5 rebalancing; check alignment of generator input shaft to PTO axis<\/p>\n<\/div>\n<\/details>\n

    \n\u26a0\ufe0f Cross-kit seizing after outdoor emergency run in rain<\/summary>\n
    \n

    Root Cause:<\/strong> Open-kit bearing cups saturated during prolonged outdoor operation in storm conditions<\/p>\n

    Fix:<\/strong> Upgrade to IP55 sealed cross-kits; grease immediately after any outdoor wet-condition operation<\/p>\n<\/div>\n<\/details>\n

    \n\u26a0\ufe0f Generator clutch slipping on motor start loads (if friction clutch fitted)<\/summary>\n
    \n

    Root Cause:<\/strong> Motor starting current creates momentary high mechanical load exceeding clutch setting<\/p>\n

    Fix:<\/strong> Increase clutch preload; or consider removing friction clutch for generator applications where electronic protection is sufficient<\/p>\n<\/div>\n<\/details>\n

    \n\u26a0\ufe0f Shaft overheating at extended continuous operation<\/summary>\n
    \n

    Root Cause:<\/strong> Insufficient grease for continuous duty; grease interval exceeded<\/p>\n

    Fix:<\/strong> Regrease; check grease volume in all nipple reservoirs; consider sealed 50-hour interval cross-kits for long-run applications<\/p>\n<\/div>\n<\/details>\n

    Australian Case Studies<\/h2>\n
    \n
    \n

    Katherine, NT<\/p>\n

    Remote cattle station \u2014 emergency flood backup generator, 45 kVA<\/p>\n

    “”After the 2022 flood isolated our property for 3 weeks, our PTO generator became our only power source. The G2.5 balanced shaft kept our refrigeration, communications, and medical equipment running flawlessly for 21 days.””<\/p>\n<\/div>\n

    \n

    Kalgoorlie, WA<\/p>\n

    Gold mine camp \u2014 off-grid 60 kVA PTO generator<\/p>\n

    “”Remote location, 1000 RPM PTO generator. Your G2.5 balanced shaft at 1000 RPM produces cleaner power than the mismatched shaft we were using \u2014 our VSD pump drives no longer produce fault alarms.””<\/p>\n<\/div>\n

    \n

    Cairns hinterland, QLD<\/p>\n

    Tropical fruit farm \u2014 post-cyclone power recovery<\/p>\n

    “”Cyclone season means we power from PTO for weeks each year. IP55 sealed cross-kits allow us to run in wet tropical conditions without stopping for bearing maintenance. Critical for our cold-chain refrigeration.””<\/p>\n<\/div>\n

    \n

    Broken Hill, NSW<\/p>\n

    Isolated station \u2014 solar-backup PTO generator<\/p>\n

    “”No grid power for 150 km. Our PTO generator runs for days at a stretch. The 50-hour sealed grease interval means we can run 2 days without interruption \u2014 previously we were stopping every 8 hours.””<\/p>\n<\/div>\n

    \n

    Shepparton, VIC<\/p>\n

    Dairy farm \u2014 storm backup for milking and cooling systems<\/p>\n

    “”SA Power Networks outages during storms mean our dairy depends on the PTO generator. The stable 50 Hz from your G2.5 shaft means our variable-speed milking equipment runs perfectly without the voltage spikes we had from our old unbalanced shaft.””<\/p>\n<\/div>\n<\/div>\n

    \u2753 Frequently Asked Questions<\/h2>\n
    \nWhy does a PTO generator need a G2.5 balanced shaft rather than the standard G6.3?<\/summary>\n
    A PTO-driven generator converts shaft rotation directly into AC electrical frequency. At 540 RPM, any shaft imbalance creates a vibration at 9 Hz (540\/60) that is superimposed on the shaft rotation. This vibration causes micro-variations in the effective rotational speed of the generator rotor \u2014 which directly manifests as frequency variation in the AC output. A G6.3 shaft can produce \u00b13% RPM variation (\u00b11.5 Hz on a 50 Hz output). A G2.5 shaft reduces this to \u00b11.2% (\u00b10.6 Hz). For sensitive agricultural electronics (variable-speed drives, computer-controlled systems, medical equipment), \u00b10.6 Hz variation is the practical limit for continuous operation without fault alarms.<\/div>\n<\/details>\n
    \nWhat PTO speed does my generator need \u2014 540 or 1000 RPM?<\/summary>\n
    This is the most critical question for generator shaft selection. A 4-pole synchronous generator (the most common type) requires 1,500 RPM for 50 Hz output, which means a 540 RPM PTO drives through a 1:2.78 step-up gearbox. A 2-pole generator requires 3,000 RPM \u2014 driven from a 1,000 RPM PTO through a 1:3 step-up gearbox. Always check the generator’s nameplate: it will state the required input RPM. Running a 540 RPM-rated generator at 1,000 RPM will cause severe over-frequency output (92.5 Hz) that can damage connected equipment instantly.<\/div>\n<\/details>\n
    \nDo I need a friction clutch on a PTO generator shaft?<\/summary>\n
    Not always. Modern PTO generators have built-in electronic current and torque limiting \u2014 when load is applied (e.g., a large motor starting), the AVR (Automatic Voltage Regulator) manages the load step without creating a torque spike to the shaft. For simple resistive loads (lighting, heating), no friction clutch is needed. For applications with large motor starting loads (irrigation pumps, compressors), a friction clutch provides an additional mechanical soft-start mechanism. If your generator has a built-in soft-start feature, the friction clutch is redundant. Consult your generator manufacturer’s guidelines.<\/div>\n<\/details>\n
    \nHow long can a PTO generator shaft run continuously?<\/summary>\n
    With IP55 sealed cross-kits and proper greasing, our Series 4\/5 generator shaft can run continuously for 50 hours between grease intervals. For longer continuous runs (>50 hours), schedule a maintenance stop for greasing \u2014 do not attempt to grease a rotating shaft. For multi-day emergency power generation, plan grease intervals in advance (e.g., at each natural break in the operation). The mechanical shaft has no inherent continuous duty limit if correctly maintained; the generator set and tractor have their own continuous duty ratings that may be more limiting.<\/div>\n<\/details>\n
    \nWhat electrical safety requirements apply to PTO generator installations in Australia?<\/summary>\n
    PTO generators that connect to a building’s electrical system must be: (1) installed by a licensed electrician; (2) fitted with appropriate transfer switching to prevent back-feeding the grid (AS 4777 compliant); (3) earth fault protected; and (4) tagged and tested per the state electrical safety act. The PTO shaft itself is a mechanical component not covered by electrical safety regulations, but it must comply with AS 4024.3601 guarding requirements as a rotating plant component. Contact your state electrical safety regulator (ESV VIC, SafeWork NSW, DNRME QLD) for current requirements in your jurisdiction.<\/div>\n<\/details>\n

    Related Products<\/h2>\n

    Our agricultural gearboxes<\/a> are precision-matched to our shaft series for seamless drivetrain integration.<\/p>\n

    \n
    \"Agricultural<\/p>\n

    Agricultural Gearbox<\/p>\n

    Bevel, inline, and custom gearboxes matched to all PTO shaft series.<\/p>\n

    View Gearboxes<\/a><\/div>\n

    \"Cross-Kits\"<\/p>\n

    Cross-Kits & Clutch Parts<\/p>\n

    Full range from Series 2 to Series 8; IP55\/IP67; cam spring sets; friction disc kits.<\/p>\n

    View Parts<\/a><\/div>\n

    \"Guards\"<\/p>\n

    Impact-Resistant Guards<\/p>\n

    5\u20137 mm impact-resistant, UV-stable, low-profile, and chemical-resistant PE guard cones.<\/p>\n

    View Guards<\/a><\/div>\n<\/div>\n

    Partner with Us<\/h2>\n
    \n

    Source Your PTO Shaft for PT<\/p>","protected":false},"excerpt":{"rendered":"

    PTO Shaft for PTO Generator & PTO Alternator \u2014 Stable Power Delivery for On-Farm Electricity Generation The PTO generator shaft \u2014 also known as a PTO alternator driveshaft, tractor generator cardan shaft, farm power generator PTO driveline, or emergency generator PTO drive shaft \u2014 connects the tractor’s power take-off to the input shaft of a […]<\/p>","protected":false},"author":1,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"_et_pb_use_builder":"","_et_pb_old_content":"","_et_gb_content_width":"","footnotes":""},"categories":[2211],"tags":[3196,1752,3197,819,1155],"class_list":["post-2285","post","type-post","status-publish","format-standard","hentry","category-pto-shaft","tag-agricultural-pto-shaft","tag-pto-drive-shaft","tag-pto-driveline","tag-pto-shaft","tag-tractor-pto-shaft"],"_links":{"self":[{"href":"https:\/\/www.agriculturalparts.top\/uk\/wp-json\/wp\/v2\/posts\/2285","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.agriculturalparts.top\/uk\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.agriculturalparts.top\/uk\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.agriculturalparts.top\/uk\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.agriculturalparts.top\/uk\/wp-json\/wp\/v2\/comments?post=2285"}],"version-history":[{"count":0,"href":"https:\/\/www.agriculturalparts.top\/uk\/wp-json\/wp\/v2\/posts\/2285\/revisions"}],"wp:attachment":[{"href":"https:\/\/www.agriculturalparts.top\/uk\/wp-json\/wp\/v2\/media?parent=2285"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.agriculturalparts.top\/uk\/wp-json\/wp\/v2\/categories?post=2285"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.agriculturalparts.top\/uk\/wp-json\/wp\/v2\/tags?post=2285"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}